The short answer
FrostPeak AC Repair repairs gas furnaces in Cupertino homes, from failed igniters and flame sensors to blower motors, thermostats, and safety switch faults. We diagnose the actual cause first, explain your repair and replacement options, and you don't have to replace a working furnace because of the Bay Area's newer appliance rules.
Cupertino winters are mild and damp rather than harsh, so most home furnaces sit idle through the long dry summer and then run mainly on cool mornings and evenings from late fall into spring. That on-and-off pattern causes its own problems: dust burning off the heat exchanger, an igniter that gives out after months of rest, a flame sensor coated with residue, or a filter nobody has changed since last winter. FrostPeak AC Repair sends technicians from our base in San Jose, about 10 miles east, to homes throughout Cupertino's 95014 ZIP code to find out why a furnace isn't heating and fix it.
Furnace Problems We See Most in Cupertino Homes
Because furnaces in the Santa Clara Valley often go months without running, many service calls come in the first cold week of the season. The furnace either won't start at all or starts, runs briefly, and shuts down. Most of these problems trace back to a few parts.
- Hot surface igniters that crack or wear out and no longer light the burners
- Dirty flame sensors that make the furnace shut off a few seconds after lighting
- Clogged filters that cause overheating and trip the high-limit switch
- Pressure switch and inducer motor faults that stop the ignition sequence
- Blower motors or capacitors that fail, so the burners run but little air reaches the rooms
- Thermostats with dead batteries, bad wiring, or incorrect settings after a summer of cooling
What Happens During a Repair Visit
Your technician starts by asking what you've noticed: odd noises, short cycling, a burning smell, cold air from the vents, or a furnace that won't respond at all. Many newer furnaces flash a fault code on a control board light, and that code points to where to look first.
From there we check the thermostat signal, the ignition sequence, gas supply to the unit, airflow, and the safety switches that protect your home. We explain what failed and why, and we tell you about your options before any work begins. If a part has to be ordered, we'll let you know and help you stay as comfortable as possible in the meantime.
Repair or Replace? What Bay Area Rules Mean for Your Furnace
Under Bay Area Air District Rule 9-4, natural gas furnaces manufactured from 2029 onward must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when a furnace is replaced after that date. These rules don't require you to replace working equipment. They apply only when an existing furnace fails or is replaced, so repairing the furnace you have is still a reasonable choice.
If your furnace is older and needs frequent repairs, it can make sense to start thinking about a heat pump now instead of during an emergency. Keep in mind that the federal 25C tax credit for heat pumps applied only to systems placed in service before December 31, 2025, and isn't available for new installations. Bay Area homeowners can still check BayREN and their local clean energy provider for current heat pump and electrification incentives. Those amounts change with each funding cycle, so we confirm the current offer before including it in any quote.
When to Turn the Furnace Off and Get Help
Some symptoms are more than an inconvenience. If you smell gas, leave the house and contact your gas utility from outside. If a carbon monoxide alarm sounds, get everyone outdoors. Turn the furnace off and call for service if you notice any of the following:
- A burning or electrical smell that continues after the first few minutes of the season
- Scorch marks or soot around the burner area
- Loud banging when the burners light
- A breaker that trips each time the furnace runs
Quick Checks Before You Call
A few simple checks can save you a visit. Make sure the thermostat is set to heat and the setpoint is above room temperature. Replace the thermostat batteries if it uses them. Confirm the furnace's power switch, which often looks like a light switch near the unit, is on, and that the furnace panel door is fully closed, since many units won't run with it loose. Check the filter and replace it if it's dirty.
If the furnace still won't heat, we can help. Along with Cupertino, we serve nearby Saratoga, Los Altos, Sunnyvale, Santa Clara, and Campbell.
More services in Cupertino
- AC Repair in Cupertino
- Heating Repair in Cupertino
- Heat Pump Installation in Cupertino
- AC Installation in Cupertino

